G. T. Abdel-jaber, A. M. Omran, K. Khalil, M. Fujii, M. Seki et al., An investigation into solidification and mechanical properties behavior of Al-Si casting alloys, Int. J. Mech. Mechatron. Eng, vol.10, issue.04, pp.30-35, 2010.

A. R. Adamane, L. Arnberg, E. E. Fiorese, G. Timelli, and F. Bonollo, Influence of injection parameters on the porosity and tensile properties of high-pressure die cast Al-Si alloys: a review, Am. Foundry Soc, vol.9, pp.43-53, 2015.

R. Ashiri, B. Niroumand, F. Karimzadeh, M. Hamani, and M. Pouranvari, Effect of casting process on microstructure and tribological behaviour of LM13 alloy, J. Alloys Compd, vol.475, pp.321-327, 2009.

R. Ashiri, F. Karimzadeh, and B. Niroumand, On effect of squeezing pressure on microstructural characteristics, heat treatment response and electrical conductivity of an Al-Si-Mg-Ni-Cu alloy, Mater. Sci. Technol, vol.30, pp.1162-1169, 2014.

L. Bäckerud, G. Chai, and J. Tamminen, Solidification characteristics of aluminum alloys. Foundry Alloys 2, 1990.

C. H. Caceres, M. B. Djurdjevic, T. J. Stockwell, and J. H. Sokolowski, The effect of Cu content on the level of microporosity in Al-Si-Cu-Mg casting alloys, Scripta Mater, vol.40, issue.5, pp.631-637, 1999.

M. S. Dargusch, G. Dour, N. Schauer, C. M. Dinnis, and G. Savage, The influence of pressure during solidification of high pressure die cast aluminium telecommunications components, J. Mater. Process. Technol, vol.180, pp.37-43, 2006.
URL : https://hal.archives-ouvertes.fr/hal-01847810

X. Fang, G. Shao, Y. Q. Liu, and Z. Fan, Effects of intensive forced melt convection on the mechanical properties of Fe containing Al-Si based alloys, Mater. Sci. Eng. A, pp.65-72, 2007.

S. Ferraro, A. Fabrizi, and G. Timelli, Evolution of sludge particles in secondary diecast aluminum alloys as function of Fe, Mn and Cr contents, Mater. Chem. Phys, vol.153, pp.168-179, 2015.

F. Grosselle, G. Timelli, F. Bonollo, and R. Molina, Correlation between microstructure and mechanical properties of Al-Si diecast engine, Metall. Sci. Technol, pp.27-29, 2009.

K. Kashyap, S. Murali, K. Raman, and K. Murthy, Casting and heat treatment variables of Al-7Si-Mg alloy, J. Mater. Sci. Technol, vol.9, pp.18-204, 1993.

Z. Ma, A. M. Samuel, F. H. Samuel, H. W. Doty, and S. Valtierra, A study of tensile properties in Al-Si-Cu and Al-Si-Mg alloys: effect of ?-iron intermetallics and porosity, Mater. Sci. Eng. A, vol.490, pp.36-51, 2008.

Z. Ma, Effect of Fe-intermetallics and Porosity on Tensile and Impact Properties of Al-S, 2002.

L. F. Mondolfo, Aluminum Alloys: Structure and Properties, 1976.

K. N. Obiekea, S. Y. Aku, and D. S. Yawas, Effects of pressure on the mechanical properties and microstructure of die cast aluminum A380 alloy, J. Miner. Mater. Charact. Eng, vol.2, pp.248-258, 2014.

S. L. Santos, R. A. Antunes, and S. F. Santos, Influence of injection temperature and pressure on the microstructure mechanical and corrosion properties of a AlSiCu alloy processed by HPDC, Mater. Des, vol.88, pp.1071-1081, 2015.

S. G. Shabestari and H. Moemeni, Effect of copper and solidification conditions on the microstructure and mechanical properties of Al-Si-Mg alloy, J. Mater. Process. Technol, pp.193-198, 2004.

S. G. Shabestari, the effect of iron and manganese on the formation of intermetallic compounds in aluminum-silicon alloys, Mater. Sci. Eng. A, vol.383, pp.289-298, 2004.

R. Taghiabadi, H. M. Ghasemi, and S. G. Shabestari, Effect of iron-rich intermetallics on the sliding wear behavior of Al-Si alloys, Mater. Sci. Eng. A, vol.490, pp.162-170, 2008.

G. Timelli and F. Bonollo, Quality mapping of aluminium alloy diecastings, Metall. Sci. Technol, vol.26, issue.1, pp.2-8, 2008.

G. Timelli and F. Bonollo, The influence of Cr content on the microstructure and mechanical properties of AlSi9Cu3 (Fe) die-casting alloys, Mater. Sci. Eng. A, vol.528, pp.273-282, 2010.

L. Wang, M. Makhlouf, and D. Apelian, Aluminium die casting alloys: alloy composition, microstructure and properties-performance relationships, Int. Mater. Rev, vol.40, pp.221-238, 1995.