T. Nakagawa, Advanced in prototype and low volume sheet forming and tooling, J. Mater. Process. Technol, vol.98, pp.244-250, 2000.

D. H. Mueller and H. Mueller, Rapid Prototyping Techniques to Manufacture Sheet Metal Forming Tools, 2000.

M. Oudjene, J. Batoz, F. Mercier, L. Penazzi, and C. Pelaingre, Mechanical analysis of prototyping tools for sheet metal stamping, Proceedings of RPD2004 Advanced Solutions and Development, 2004.

H. Muller and J. Sladojevic, Rapid tooling approaches for small lot production of sheet metal parts, J. Mater. Process. Technol, vol.115, pp.97-105, 2001.

D. F. Walczyk and D. H. Hardt, Design and analysis of recomfortable discrete dies for sheet metal forming, J. Manuf. Syst, vol.17, issue.6, pp.436-454, 1998.

D. F. Walczyk and D. H. Hardt, Rapid tooling for sheet metal forming using profiled edge laminations-design principles and demonstration, J. Manuf. Syst, vol.120, pp.746-754, 1998.

D. F. Walczyk and D. H. Hardt, A comparison of rapid fabrication methods for sheet metal forming dies, J. Manuf. Syst, vol.121, pp.214-224, 1999.
DOI : 10.1115/1.2831208

P. M. Dickens, Principles of design for laminated tooling, Int. J. Prod. Res, vol.35, issue.N5, pp.1349-1357, 1997.
DOI : 10.1080/002075497195362

C. Abel, L. Velnom, C. Barlier, and P. Poirier, Deux projets européens de recherche collaborative en PME (CRAFT)-Intégration du procédé de Stratoconception ® en outillage rapide direct pour l'injection, l'emboutissage et la fonderie sous pression, pp.1-3, 2003.

B. Wadman, Fluid cell forming tools produced by different rapid prototyping methods, Proceedings of the 22th International Deep Drawing Research Group Congress, pp.205-214, 2003.

M. Oudjene, F. Mercier, L. Penazzi, and J. Batoz, 3D finite element modeling and analysis of the laminated tooling behaviour in sheet metal stamping process, Proceedings of the 24th International Deep Drawing Research Group Congress, p.10, 2005.
URL : https://hal.archives-ouvertes.fr/hal-01796833

M. Oudjene, Modélisation et optimisation du comportement mécanique des outils d'emboutissage stratifiés précontraints par vissage, 2005.

T. Pepelnjak and K. Kuzman, Adaptable tooling sets for metal forming of geometrically similar products, J. Mater. Process. Technol, vol.80, pp.413-420, 1998.
DOI : 10.1016/s0924-0136(98)00120-4

J. Dankert, Reduction of the residual stresses in a deep-drawing cup by modifying the draw die profile, CIRP, vol.44, p.1, 1995.

F. F. Damborg, M. R. Jensen, K. B. Nielsen, and J. Dankert, Optimization of the draw die profile with regard to wear using the FEM, Proceedings of the 19th International Deep Drawing Research Group Congress, 1996.

M. Burlat, Analyse Mécanique et Tribologique de l'Emboutissage: application aux Outils fabriqués par combinaison de différents matériaux, 1998.

, Proceedings of the 2nd International Conference Numerical Simulation of 3-D Sheet Metal Forming Processes-Verification of Simulation with Experiments (Numisheet'2002), 2002.

A. T. Quantech, Stampack User Guide-Version 5.6, Quantech edt, 2004.

M. Yoneno, T. Sawa, and T. Ishihara, The strength of joints combining adhesives with bolts (case where adherends are pipe flanges of which the interfaces are bonded partially), JSME Int. J., Ser. A, vol.42, issue.1, pp.126-134, 1999.

, Régles de calcul des constructions en acier "Régles CM66, Editions Eyrolles, 1995.