A. Adibi-sedeh, M. Vaziri, V. Pednekar, V. Madhavan, and R. Ivester, Investigation of the Effect of Using Different Material Models on Finite Element Simulations of Machining, Proceedings of the 8th CIRP International Workshop on Modelling of Machining Operations, pp.1-9, 2005.

F. Ambrosy, F. Zanger, and V. Schulze, FEM-simulation of machining induced nanocrystalline surface layers in steel surfaces prepared for tribological applications, CIRP Annals, vol.64, issue.1, pp.69-72, 2015.
DOI : 10.1016/j.cirp.2015.04.063

J. Anderson and O. Saunders, Convection from an Isolated Heated Horizontal Cylinder Rotating about Its Axis, Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences, vol.217, issue.1131, pp.555-562, 1131.
DOI : 10.1098/rspa.1953.0080

U. Andrade, M. Meyers, K. Vecchio, and A. Chokshi, Dynamic recrystallization in high-strain, high-strain-rate plastic deformation of copper, Acta Metallurgica et Materialia, vol.42, issue.9, pp.3183-3195, 1994.
DOI : 10.1016/0956-7151(94)90417-0

Y. Arisoy and T. Özel, Prediction of machining induced microstructure in Ti???6Al???4V alloy using 3-D FE-based simulations: Effects of tool micro-geometry, coating and cutting conditions, Journal of Materials Processing Technology, vol.220, pp.1-26, 2015.
DOI : 10.1016/j.jmatprotec.2014.11.002

P. Arrazola, M. Saez-de-buruaga, and I. Arrieta, Innovative Method Dedicated to the Development of a Ferrite-pearlite Grade Regarding its Machinability, 2006.

P. Arrazola, D. Ugarte, and X. Dominguez, A new approach for the friction identification during machining through the use of finite element modeling, International Journal of Machine Tools and Manufacture, vol.48, issue.2, pp.173-183, 2008.
DOI : 10.1016/j.ijmachtools.2007.08.022

P. Arrazola and T. Özel, Finite Element Modelling of Machining Processes. Intelligent Machining: Modelling and Optimization of the Machining Processes and Systems, 2009.

P. Arrazola and T. Özel, Investigations on the effects of friction modeling in finite element simulation of machining, International Journal of Mechanical Sciences, vol.52, issue.1, pp.31-42, 2010.
DOI : 10.1016/j.ijmecsci.2009.10.001

P. Arrazola, T. Özel, D. Umbrello, M. Davies, and I. Jawahir, Recent advances in modelling of metal machining processes, CIRP Annals, vol.62, issue.2, pp.695-718, 2013.
DOI : 10.1016/j.cirp.2013.05.006

V. Astakhov, Tribology of Metal Cutting, 2006.

V. Astakhov, Tribology of Cutting Tools, Tribology in Manufacturing Technology, vol.1, pp.1-66, 2013.
DOI : 10.1007/978-3-642-31683-8_1

V. Astakhov, Metal Cutting Mechanics, 1998.

A. Atkins, Modelling metal cutting using modern ductile fracture mechanics: quantitative explanations for some longstanding problems, International Journal of Mechanical Sciences, vol.45, issue.2, pp.373-396, 2003.
DOI : 10.1016/S0020-7403(03)00040-7

S. Atlati, B. Haddag, M. Nouari, and A. Moufki, Effect of the local friction and contact nature on the Built-Up Edge formation process in machining ductile metals, Tribology International, vol.90, pp.217-227, 2015.
DOI : 10.1016/j.triboint.2015.04.024

URL : https://hal.archives-ouvertes.fr/hal-01417920

S. Atlati, B. Haddag, M. Nouari, and M. Zenasni, Thermomechanical modelling of the tool???workmaterial interface in machining and its implementation using the ABAQUS VUINTER subroutine, International Journal of Mechanical Sciences, vol.87, pp.102-117, 2014.
DOI : 10.1016/j.ijmecsci.2014.05.034

URL : https://hal.archives-ouvertes.fr/hal-01424972

Z. Atmani, B. Haddag, M. Nouari, and M. Zenasni, Combined microstructure-based flow stress and grain size evolution models for multi-physics modelling of metal machining, International Journal of Mechanical Sciences, vol.118, pp.77-90, 2016.
DOI : 10.1016/j.ijmecsci.2016.09.016

M. Attia, D. Silva, and N. , Thermal Analysis of the Fuel Bearing Pad in the CANDU Reactor?Prediction of Nucleate Boiling, Proceedings of the 3rd Multiphase Flow and Heat Transfer Symposium, pp.851-863, 1983.

M. Attia, P. Joseph, M. Saoubi, and R. , Determination of convective heat transfer from rotating workpieces in dry and laser-assisted turning processes, Advances in Materials and Processing Technologies, pp.324-338, 2016.
DOI : 10.1007/BF01783615

M. Attia and L. Kops, Computer Simulation of Nonlinear Thermoelastic Behavior of a Joint in Machine Tool Structure and its Effect on Thermal Deformation, Journal of Engineering for Industry, vol.101, issue.3, pp.355-361, 1979.
DOI : 10.1115/1.3439518

M. Attia and L. Kops, Nonlinear Thermoelastic Behavior of Structural Joints???Solution to a Missing Link for Prediction of Thermal Deformation of Machine Tools, Journal of Engineering for Industry, vol.101, issue.3, pp.348-354, 1979.
DOI : 10.1115/1.3439517

M. Attia and L. Kops, Importance of Contact Pressure Distribution on Heat Transfer in Structural Joints of Machine Tools, Journal of Engineering for Industry, vol.102, issue.2, pp.159-167, 1980.
DOI : 10.1115/1.3183848

M. Attia and L. Kops, System Approach to the Thermal Behavior and Deformation of Machine Tool Structures in Response to the Effect of Fixed Joints, Journal of Engineering for Industry, vol.103, issue.1, pp.67-72, 1981.
DOI : 10.1115/1.3184461

M. Attia and L. Kops, A New Approach to Cutting Temperature Prediction Considering the Thermal Constriction Phenomenon in Multi-layer Coated Tools, CIRP Annals, vol.53, issue.1, pp.47-52, 2004.
DOI : 10.1016/S0007-8506(07)60642-8

M. Attia and L. Kops, Thermal Consideration of the Design of Multi-Layer Coated Tools for High Speed Machining, Proceedings of the ASME International Mechanical Engineering Congress & Exposition, pp.803-813, 2004.

V. Bacherla and J. Bassani, Strain burst phenomena in the necking of a sheet that deforms by non-associated plastic flow, Modelling and Simulation in Materials Science and Engineering, vol.15, issue.1, p.297, 2007.
DOI : 10.1088/0965-0393/15/1/S23

Y. Bai and T. Wierzbicki, A new model of metal plasticity and fracture with pressure and Lode dependence, International Journal of Plasticity, vol.24, issue.6, pp.1071-1096, 2008.
DOI : 10.1016/j.ijplas.2007.09.004

P. Bariani, D. Negro, T. Bruschi, and S. , Testing and Modelling of Material Response to Deformation in Bulk Metal Forming, CIRP Annals, vol.53, issue.2, pp.573-595, 2004.
DOI : 10.1016/S0007-8506(07)60030-4

R. Barron and R. Stanley, Film Boiling Under an Impinging Cryogenic Jet, Advances in Cryogenic Engineering, vol.39, pp.1769-1777, 1994.
DOI : 10.1007/978-1-4615-2522-6_216

S. Basu and M. Shankar, Spatial confinement-induced switchover in microstructure evolution during severe plastic deformation at micrometer length scales, Acta Materialia, vol.79, pp.146-158, 2014.
DOI : 10.1016/j.actamat.2014.07.004

S. Basu and M. Shankar, Crystallographic Textures Resulting from Severe Shear Deformation in Machining, Metallurgical and Materials Transactions A, vol.394, issue.2, pp.801-812, 2015.
DOI : 10.1016/j.msea.2004.11.032

S. Basu, Z. Wang, R. Liu, and C. Saldana, Enhanced subsurface grain refinement during transient shear-based surface generation, Acta Materialia, vol.116, pp.114-123, 2016.
DOI : 10.1016/j.actamat.2016.06.033

K. Becker, Measurements of convective heat transfer from a horizontal cylinder rotating in a tank of water, International Journal of Heat and Mass Transfer, vol.6, issue.12, pp.1053-1062, 1963.
DOI : 10.1016/0017-9310(63)90006-1

H. Bil, S. Kilic, and A. Tekkaya, A comparison of orthogonal cutting data from experiments with three different finite element models, International Journal of Machine Tools and Manufacture, vol.44, issue.9, pp.933-944, 2004.
DOI : 10.1016/j.ijmachtools.2004.01.016

P. Bollig, C. Faltin, R. Schiel, J. Schneider, U. Maas et al., Considering the Influence of Minimum Quantity Lubrication for Modelling Changes in Temperature, Forces and Phase Transformations during Machining, Procedia CIRP, vol.31, pp.142-147, 2015.
DOI : 10.1016/j.procir.2015.03.025

C. Bonnet, E. Valiorgue, J. Rech, and H. Hamdi, Improvement of the numerical modeling in orthogonal dry cutting of an AISI 316L stainless steel by the introduction of a new friction model, CIRP Journal of Manufacturing Science and Technology, vol.1, issue.2, pp.114-118, 2008.
DOI : 10.1016/j.cirpj.2008.09.006

T. Brown, C. Saldana, T. Murthy, J. Mann, Y. Guo et al., A study of the interactive effects of strain, strain rate and temperature in severe plastic deformation of copper, Acta Materialia, vol.57, issue.18, pp.5491-5500, 2000.
DOI : 10.1016/j.actamat.2009.07.052

S. Buchkremer, B. Wu, D. Lung, S. Münstermann, F. Klocke et al., FE-simulation of machining processes with a new material model, Journal of Materials Processing Technology, vol.214, issue.3, pp.599-611, 2014.
DOI : 10.1016/j.jmatprotec.2013.10.014

T. Burns, S. Mates, R. Rhorer, E. Whitenton, and D. Basak, DYNAMIC PROPERTIES FOR MODELING AND SIMULATION OF MACHINING: EFFECT OF PEARLITE TO AUSTENITE PHASE TRANSITION ON FLOW STRESS IN AISI 1075 STEEL, Machining Science and Technology, vol.76, issue.15, pp.1-20, 2011.
DOI : 10.1016/S0890-6955(02)00046-9

F. Cabanettes, R. J. Dumont, F. Rech, J. Dimkowski, and Z. , Influence of Minimum Quantity Lubrication on Friction Characterizing Tool???Aluminum Alloy Contact, Journal of Tribology, vol.138, issue.2, p.21107, 2010.
DOI : 10.1115/1.4031990

M. Calamaz, D. Coupard, and F. Girot, A new material model for 2D numerical simulation of serrated chip formation when machining titanium alloy Ti???6Al???4V, International Journal of Machine Tools and Manufacture, vol.48, issue.3-4, pp.3-4275, 2008.
DOI : 10.1016/j.ijmachtools.2007.10.014

URL : https://hal.archives-ouvertes.fr/hal-00911076

R. Calistes, S. Swaminathan, T. Murthy, C. Huang, C. Saldana et al., Controlling gradation of surface strains and nanostructuring by large-strain machining, Scripta Materialia, vol.60, issue.1, pp.17-20, 2009.
DOI : 10.1016/j.scriptamat.2008.08.027

S. Caruso, D. Renzo, S. Umbrello, D. Jayal, A. Dillon et al., Finite Element Modeling of Microstructural Changes in Hard Turning, Advanced Materials Research, vol.223, pp.960-968, 2011.
DOI : 10.4028/www.scientific.net/AMR.223.960

O. Cazacu, B. Plunkett, and F. Barlat, Orthotropic yield criterion for hexagonal closed packed metals, International Journal of Plasticity, vol.22, issue.7, pp.1171-1194, 2006.
DOI : 10.1016/j.ijplas.2005.06.001

B. Chaparro, S. Thuillier, L. Menezes, P. Manach, and J. Fernandes, Material parameters identification: Gradient-based, genetic and hybrid optimization algorithms, Computational Materials Science, vol.44, issue.2, pp.339-346, 2008.
DOI : 10.1016/j.commatsci.2008.03.028

URL : https://hal.archives-ouvertes.fr/hal-00404004

S. Chen, J. Kothari, and A. Tseng, Spray and jet cooling in steel rolling, International Journal of Heat and Fluid Flow, vol.13, issue.4, pp.358-369, 1992.
DOI : 10.1016/0142-727X(92)90006-U

S. Chen, J. Kothari, and A. Tseng, Cooling of a moving plate with an impinging circular water jet, Experimental Thermal and Fluid Science, vol.4, issue.3, pp.343-353, 1991.
DOI : 10.1016/0894-1777(91)90051-R

T. Childs, Rake Face Action of Cutting Lubricants: An Analysis of, and Experiments on, the Machining of Iron Lubricated by Carbon Tetrachloride, Proceedings of the Institution of Mechanical Engineers, vol.186, issue.1, pp.717-727, 1973.
DOI : 10.1243/PIME_PROC_1972_186_088_02

T. Childs, Material Property Requirements for Modelling Metal Machining, C3). C3-XXI-C3-XXXVI, 1997.
DOI : 10.1051/jp4:1997301

URL : https://hal.archives-ouvertes.fr/jpa-00255374

T. Childs, Friction modelling in metal cutting, Wear, vol.260, issue.3, pp.310-318, 2006.
DOI : 10.1016/j.wear.2005.01.052

T. Childs, Numerical experiments on the influence of material and other variables on plane strain continuous chip formation in metal machining, International Journal of Mechanical Sciences, vol.48, issue.3, pp.307-322, 2006.
DOI : 10.1016/j.ijmecsci.2005.09.012

T. Childs, Modelling orthogonal machining of carbon steels. Part I: Strain hardening and yield delay effects, International Journal of Mechanical Sciences, vol.51, issue.5, pp.402-411, 2009.
DOI : 10.1016/j.ijmecsci.2009.03.007

T. Childs, Surface energy, cutting edge radius and material flow stress size effects in continuous chip formation of metals, CIRP Journal of Manufacturing Science and Technology, vol.3, issue.1, pp.27-39, 2010.
DOI : 10.1016/j.cirpj.2010.07.008

T. Childs, K. Maekawa, and P. Maulik, Effects of coolant on temperature distribution in metal machining, Materials Science and Technology, vol.211, issue.11, pp.1006-1019, 1988.
DOI : 10.1016/0017-9310(70)90113-4

T. Childs, K. Maekawa, T. Obikawa, and Y. Yamane, Metal Machining: Theory and Applications, 2000.

T. Childs and R. Rahmad, Modelling orthogonal machining of carbon steels. Part II: Comparisons with experiments, International Journal of Mechanical Sciences, vol.51, issue.6, pp.465-472, 2009.
DOI : 10.1016/j.ijmecsci.2009.04.001

T. Childs and R. Rahmad, Modifying strain-hardening of carbon steels for improved finite element simulation of orthogonal machining, Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, vol.185, issue.5, pp.721-731, 2010.
DOI : 10.1243/PIME_PROC_1970_185_088_02

Y. Chou and C. Evans, White layers and thermal modeling of hard turned surfaces, International Journal of Machine Tools and Manufacture, vol.39, issue.12, pp.1863-1881, 1999.
DOI : 10.1016/S0890-6955(99)00036-X

L. Chuzhoy, R. Devor, S. Kapoor, and G. Bammann, Microstructure-Level Modeling of Ductile Iron Machining, Journal of Manufacturing Science and Engineering, vol.124, issue.2, pp.162-169, 2002.
DOI : 10.1115/1.1455642

C. Claudin, A. Mondelin, J. Rech, and G. Fromentin, Effects of a straight oil on friction at the tool???workmaterial interface in machining, International Journal of Machine Tools and Manufacture, vol.50, issue.8, pp.681-688, 2010.
DOI : 10.1016/j.ijmachtools.2010.04.013

URL : https://hal.archives-ouvertes.fr/hal-00880781

J. Collier and J. Thome, Convective Boiling and Condensation, 1994.

C. Courbon, T. Mabrouki, J. Rech, D. Mazuyer, D. Eramo et al., New Thermal Issues on the Modelling of Tool-Workpiece Interaction: Application to Dry Cutting of AISI 1045 Steel, Advanced Materials Research, vol.223, pp.286-295, 2011.
DOI : 10.4028/www.scientific.net/AMR.223.286

URL : https://hal.archives-ouvertes.fr/hal-00629453

C. Courbon, T. Mabrouki, J. Rech, D. Mazuyer, D. Eramo et al., On the existence of a thermal contact resistance at the tool-chip interface in dry cutting of AISI 1045: Formation mechanisms and influence on the cutting process, Applied Thermal Engineering, vol.50, issue.1, pp.1311-1325, 2013.
DOI : 10.1016/j.applthermaleng.2012.06.047

URL : https://hal.archives-ouvertes.fr/hal-00938561

C. Courbon, T. Mabrouki, J. Rech, D. Mazuyer, F. Perrard et al., Towards a Physical FE Modelling of a Dry Cutting Operation: Influence of Dynamic Recrystallization When Machining AISI 1045, Procedia CIRP, vol.8, pp.516-521, 2013.
DOI : 10.1016/j.procir.2013.06.143

M. Davies, T. Ueda, M. Saoubi, R. Mullany, B. Cooke et al., On The Measurement of Temperature in Material Removal Processes, CIRP Annals, vol.56, issue.2, pp.581-604, 2007.
DOI : 10.1016/j.cirp.2007.10.009

L. Denguir, J. Outeiro, G. Fromentin, V. Vignal, and R. Besnard, Orthogonal Cutting Simulation of OFHC Copper Using a New Constitutive Model Considering the State of Stress and the Microstructure Effects, Procedia CIRP, vol.46, pp.238-241, 2016.
DOI : 10.1016/j.procir.2016.03.208

URL : https://hal.archives-ouvertes.fr/hal-01333567

V. Dhir, Nucleate and transition boiling heat transfer under pool and external flow conditions, International Journal of Heat and Fluid Flow, vol.12, issue.4, pp.290-314, 1991.
DOI : 10.1016/0142-727X(91)90018-Q

H. Ding and Y. Shin, Modeling of grain refinement in aluminum and copper subjected to cutting, Computational Materials Science, vol.50, issue.10, pp.3016-3025, 2011.
DOI : 10.1016/j.commatsci.2011.05.020

H. Ding and Y. Shin, Dislocation Density-Based Grain Refinement Modeling of Orthogonal Cutting of Titanium, Journal of Manufacturing Science and Engineering, vol.136, issue.4, pp.41003-41004, 2014.
DOI : 10.1115/1.4027207

G. Dreitser, Modern Problems of Cryogenic Heat Transfer and its Enhancement (Generalization of Experimental Results, Practical Recommendations and Different Applications), Low Temperature and Cryogenic Refrigeration, pp.201-220, 2003.
DOI : 10.1007/978-94-010-0099-4_12

D. Dropkin and A. Carmi, Natural Convection Heat Transfer from a Horizontal Cylinder Rotating in Air, Transactions of ASME, vol.79, issue.4, pp.741-749, 1957.

A. Elsayed, M. Attia, and A. Damir, Computer Fluid Dynamics Analysis for Enhanced Cooling of Cutting Tools in Turning Operation, Internal Report, Structures , Materials and Manufacturing Laboratory, 2016.

A. Elshwain, N. Redzuan, and N. Yusof, Machinability of Nickel and Titanium Alloys Under of Gas-based Coolant-lubricants (Cls)?A Review, International Journal of Research in Engineering and Technology, vol.2, issue.11, pp.690-702, 2013.

Y. Estrin, L. Toth, A. Molinari, and Y. Brechet, A dislocation-based model for all hardening stages in large strain deformation, Acta Materialia, vol.46, issue.15, pp.5509-5522, 1998.
DOI : 10.1016/S1359-6454(98)00196-7

A. Etemad, Free Convection Heat Transfer from a Rotating Cylinder to Ambient Air with Interferometric Study of Flow, Transactions of ASME, vol.77, pp.1283-1289, 1955.

M. Fahad, P. Mativenga, and M. Sheikh, -TiN) tungsten carbide tools in high speed cutting using a hybrid finite element and experimental technique, Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, vol.2, issue.2, pp.1835-1850, 2011.
DOI : 10.1016/S1526-6125(00)70015-6

P. Faverjon, J. Rech, and R. Leroy, Influence of Minimum Quantity Lubrication on Friction Coefficient and Work-Material Adhesion During Machining of Cast Aluminum With Various Cutting Tool Substrates Made of Polycrystalline Diamond, High Speed Steel, and Carbides, Journal of Tribology, vol.135, issue.4, p.41602, 2013.
DOI : 10.1115/1.4024546

O. Fergani, A. Tabei, H. Garmestani, and S. Liang, Prediction of polycrystalline materials texture evolution in machining via Viscoplastic Self-Consistent modeling, Journal of Manufacturing Processes, vol.16, issue.4, pp.543-550, 2014.
DOI : 10.1016/j.jmapro.2014.07.004

J. Field, S. Walley, W. Proud, H. Goldrein, and C. Siviour, Review of experimental techniques for high rate deformation and shock studies, International Journal of Impact Engineering, vol.30, issue.7, pp.725-775, 2004.
DOI : 10.1016/j.ijimpeng.2004.03.005

L. Filice, F. Micari, S. Rizzuti, and D. Umbrello, A critical analysis on the friction modelling in orthogonal machining, International Journal of Machine Tools and Manufacture, vol.47, issue.3-4, pp.709-714, 2007.
DOI : 10.1016/j.ijmachtools.2006.05.007

L. Filice, F. Micari, S. Rizzuti, and D. Umbrello, DEPENDENCE OF MACHINING SIMULATION EFFECTIVENESS ON MATERIAL AND FRICTION MODELLING, Machining Science and Technology, vol.17, issue.3, pp.370-389, 2008.
DOI : 10.1081/MST-200051211

L. Filice, D. Umbrello, F. Micari, and L. Settineri, On the Finite Element Simulation of Thermal Phenomena in Machining Processes, Advanced Methods in Material Forming, pp.263-278, 2007.
DOI : 10.1007/3-540-69845-0_16

P. Follansbee and U. Kocks, A constitutive description of the deformation of copper based on the use of the mechanical threshold stress as an internal state variable, Acta Metallurgica, vol.36, issue.1, pp.81-93, 1988.
DOI : 10.1016/0001-6160(88)90030-2

G. Germain, A. Morel, and T. Braham-bouchnak, Identification of Material Constitutive Laws Representative of Machining Conditions for Two Titanium Alloys: Ti6Al4V and Ti555-3, Journal of Engineering Materials and Technology, vol.135, issue.3, p.31002, 2013.
DOI : 10.1115/1.4023674

L. Giannuzzi and S. F. , A review of focused ion beam milling techniques for TEM specimen preparation, Micron, vol.30, issue.3, pp.197-204, 1999.
DOI : 10.1016/S0968-4328(99)00005-0

R. Goldstein and M. Franchett, Heat Transfer From a Flat Surface to an Oblique Impinging Jet, Journal of Heat Transfer, vol.110, issue.1, pp.84-90, 1988.
DOI : 10.1115/1.3250477

W. Grzesik, Experimental investigation of the cutting temperature when turning with coated indexable inserts, International Journal of Machine Tools and Manufacture, vol.39, issue.3, pp.355-369, 1999.
DOI : 10.1016/S0890-6955(98)00044-3

W. Grzesik, Experimental investigation of the influence of adhesion on the frictional conditions in the cutting process, Tribology International, vol.32, issue.1, pp.131-140, 1999.
DOI : 10.1016/S0301-679X(99)00004-3

W. Grzesik, The influence of thin hard coatings on frictional behaviour in the orthogonal cutting process, Tribology International, vol.33, issue.2, pp.131-140, 2000.
DOI : 10.1016/S0301-679X(00)00072-4

W. Grzesik, Advanced Machining Processes of Metallic Materials, 2008.

W. Grzesik, B. Denkena, Z. K. Grove, T. Bergman, and B. , Correlation Between Friction and Wear of Cubic Borone Nitride Cutting Tools in Precision Hard Machining, Journal of Manufacturing Science and Engineering, vol.138, issue.3, p.31010, 2015.
DOI : 10.1115/1.4031189

W. Grzesik, B. Denkena, Z. K. Grove, T. Bergman, and B. , Energy consumption characterization in precision hard machining using CBN cutting tools, The International Journal of Advanced Manufacturing Technology, vol.34, issue.5, pp.2839-2845, 2016.
DOI : 10.1007/s00170-006-0737-6

W. Grzesik and P. Nielsony, Prediction of friction and heat flow in machining incorporating thermophysical properties of the coating???chip interface, Wear, vol.256, issue.1-2, pp.108-117, 2004.
DOI : 10.1016/S0043-1648(03)00390-9

W. Grzesik and P. Nielsony, Thermophysical-Property-Based Selection of Tool Protective Coatings for Dry Machining of Steels, Journal of Manufacturing Science and Engineering, vol.125, issue.4, pp.689-695, 2003.
DOI : 10.1115/1.1617982

W. Grzesik and P. Nielsony, Physics based modelling of interface temperatures in machining with multilayer coated tools at moderate cutting speeds, International Journal of Machine Tools and Manufacture, vol.44, issue.9, pp.889-901, 2004.
DOI : 10.1016/j.ijmachtools.2004.02.014

W. Grzesik, J. Rech, and Z. K. , Determination of friction in metal cutting with tool wear and flank face effects, Wear, vol.317, issue.1-2, pp.8-10, 2014.
DOI : 10.1016/j.wear.2014.05.003

W. Grzesik and C. Van-luttervelt, An Investigation of the Thermal Effects in Orthogonal Cutting Associated with Multilayer Coatings, CIRP Annals, vol.50, issue.1, pp.53-56, 2001.
DOI : 10.1016/S0007-8506(07)62069-1

W. Grzesik and Z. K. , Friction quantification in the oblique cutting with CBN chamfered tools, Wear, vol.304, issue.1-2, pp.36-42, 2013.
DOI : 10.1016/j.wear.2013.04.020

P. Gulati, V. Katti, and S. Prabhu, Influence of the shape of the nozzle on local heat transfer distribution between smooth flat surface and impinging air jet, International Journal of Thermal Sciences, vol.48, issue.3, pp.602-617, 2009.
DOI : 10.1016/j.ijthermalsci.2008.05.002

Y. Guo, C. Saldana, W. Compton, and S. Chandrasekar, Controlling deformation and microstructure on machined surfaces, Acta Materialia, vol.59, issue.11, pp.4538-4547, 2011.
DOI : 10.1016/j.actamat.2011.03.076

Y. Guo, Q. Wen, and K. Woodbury, Dynamic Material Behavior Modeling Using Internal State Variable Plasticity and Its Application in Hard Machining Simulations, Journal of Manufacturing Science and Engineering, vol.128, issue.3, pp.749-759, 2006.
DOI : 10.1115/1.2193549

M. Hadad and B. Sadeghi, Thermal analysis of minimum quantity lubrication-MQL grinding process, International Journal of Machine Tools and Manufacture, vol.63, pp.1-15, 2012.
DOI : 10.1016/j.ijmachtools.2012.07.003

M. Hadad, T. Tawakoli, M. Sadeghi, and B. Sadeghi, Temperature and energy partition in minimum quantity lubrication-MQL grinding process, International Journal of Machine Tools and Manufacture, vol.54, issue.55, pp.10-17, 2012.
DOI : 10.1016/j.ijmachtools.2011.11.010

A. Haglund, H. Kishawy, and R. Rogers, An exploration of friction models for the chip???tool interface using an Arbitrary Lagrangian???Eulerian finite element model, Wear, vol.265, issue.3-4, pp.3-4452, 2008.
DOI : 10.1016/j.wear.2007.11.025

J. Hamann, F. Meslin, and J. Sartkulvanich, CRITERIA FOR THE QUALITY ASSESSMENT OF CONSTITUTIVE EQUATIONS DEDICATED TO CUTTING MODELS, Machining Science and Technology, vol.8, issue.3, pp.331-351, 2002.
DOI : 10.1016/S0924-0136(96)02436-3

P. Hedenquist and M. Olsson, Sliding Wear Testing of Coated Cutting Tool Materials, Tribology International, vol.23, issue.3, pp.143-150, 1991.

C. Ho, R. Powell, and P. Liley, Thermal Conductivity of the Elements, Journal of Physical and Chemical Reference Data, vol.1, issue.2, 1974.
DOI : 10.1063/1.3253100

K. Holmberg and A. Matthews, Properties, Techniques and Applications in Surface Engineering, Coating Tribology, 1998.

T. Holmquist and G. Johnson, DETERMINATION OF CONSTANTS AND COMPARISON OF RESULTS FOR VARIOUS CONSTITUTIVE MODELS, Le Journal de Physique IV, vol.01, issue.C3, pp.3-853, 1991.
DOI : 10.1051/jp4:19913119

URL : https://hal.archives-ouvertes.fr/jpa-00249922

A. Hor, F. Morel, J. Lebrun, and G. Germain, Modelling, identification and application of phenomenological constitutive laws over a large strain rate and temperature range, Mechanics of Materials, vol.64, pp.91-110, 2013.
DOI : 10.1016/j.mechmat.2013.05.002

URL : https://hal.archives-ouvertes.fr/hal-01133909

C. Huang, T. Murthy, M. Shankar, M. Saoubi, R. Chandrasekar et al., Temperature rise in severe plastic deformation of titanium at small strain-rates, Scripta Materialia, vol.58, issue.8, pp.663-666, 2008.
DOI : 10.1016/j.scriptamat.2007.11.042

D. Hughes and N. Hansen, High angle boundaries formed by grain subdivision mechanisms, Acta Materialia, vol.45, issue.9, pp.3871-3886, 1997.
DOI : 10.1016/S1359-6454(97)00027-X

F. Itoigawa, D. Takeuchi, T. Nakamura, and T. Childs, Experimental Study of Lubrication Mechanism in MQL Intermittent Cutting Process, Machining Science and Technology, vol.11, issue.3, pp.355-365, 2007.

R. Ivester, E. Whitenton, and L. Deshayes, Comparison of Measurements and Simulation for Machining of Aluminum. Transactions of the North American Manufacturing Research Institution, SME, vol.33, pp.429-436, 2005.

K. Iwata, K. Osakada, and X. Teresaka, Process Modeling of Orthogonal Cutting by the Rigid-Plastic Finite Element Method, Journal of Engineering Materials and Technology, vol.106, issue.2, pp.132-138, 1984.
DOI : 10.1115/1.3225687

F. Jafarian, M. Ciaran, D. Umbrello, P. Arrazola, L. Filice et al., Finite element simulation of machining Inconel 718 alloy including microstructure changes, International Journal of Mechanical Sciences, vol.88, pp.110-121, 2014.
DOI : 10.1016/j.ijmecsci.2014.08.007

K. Jambunathan, E. Lai, M. Moss, and B. Button, A review of heat transfer data for single circular jet impingement, International Journal of Heat and Fluid Flow, vol.13, issue.2, pp.106-115, 1992.
DOI : 10.1016/0142-727X(92)90017-4

S. Jaspers and J. Dautzenberg, Material behaviour in conditions similar to metal cutting: flow stress in the primary shear zone, Journal of Materials Processing Technology, vol.122, issue.2-3, pp.2-3322, 2002.
DOI : 10.1016/S0924-0136(01)01228-6

I. Jawahir, M. Attia, D. Biermann, J. Duflou, F. Klocke et al., Cryogenic manufacturing processes, CIRP Annals, vol.65, issue.2, pp.713-736, 2016.
DOI : 10.1016/j.cirp.2016.06.007

I. Jawahir, E. Brinksmeier, M. Saoubi, R. Aspinwall, D. Outeiro et al., Surface integrity in material removal processes: Recent advances, Surface Integrity in Material Removal Processes: Recent Advances, pp.603-626, 2011.
DOI : 10.1016/j.cirp.2011.05.002

L. Jiang, A. Roos, and P. Liu, The influence of austenite grain size and its distribution on chip deformation and tool life during machining of AISI 304L, Metallurgical and Materials Transactions A, vol.22, issue.11, pp.2415-2422, 1997.
DOI : 10.1016/0921-5093(89)90871-X

T. Jin, D. Stephenson, and W. Rowe, Estimation of the convection heat transfer coefficient of coolant within the grinding zone, Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, vol.17, issue.2, pp.397-407, 2003.
DOI : 10.1016/S0007-8506(07)60814-2

G. Johnson and W. Cook, A Constitutive Model and Data for Metals Subjected to High Strains, High Strain Rates, and High Temperatures. Proceedings of the 7th International Symposium on Ballistics, pp.541-547, 1983.

G. Johnson and W. Cook, Fracture characteristics of three metals subjected to various strains, strain rates, temperatures and pressures, Engineering Fracture Mechanics, vol.21, issue.1, pp.31-48, 1985.
DOI : 10.1016/0013-7944(85)90052-9

P. Joseph, M. Attia, and B. Shi, Experimental and Numerical Analysis of Heat Transfer in CVD Coated Carbide Tools, 2016.

N. Kim, C. Guo, and S. Malkin, Heat Flux Distribution and Energy Partition in Creep-Feed Grinding, CIRP Annals, vol.46, issue.1, pp.227-232, 1997.
DOI : 10.1016/S0007-8506(07)60814-2

F. Klocke and T. Krieg, Coated Tools for Metal Cutting ??? Features and Applications, CIRP Annals, vol.48, issue.2, pp.515-525, 1999.
DOI : 10.1016/S0007-8506(07)63231-4

H. Kolsky, An Investigation of the Mechanical Properties of Materials at very High Rates of Loading, Proceedings of the Physical Society. Section B, vol.62, issue.11, pp.676-700, 1949.
DOI : 10.1088/0370-1301/62/11/302

R. Komanduri, Some clarifications on the mechanics of chip formation when machining titanium alloys, Wear, vol.76, issue.1, pp.15-34, 1982.
DOI : 10.1016/0043-1648(82)90113-2

W. König, R. Fritsch, and D. Kammermeier, New Approaches to Characterizing the Performance of Coated Cutting Tools, CIRP Annals, vol.41, issue.1, pp.49-54, 1992.
DOI : 10.1016/S0007-8506(07)61150-0

E. Kopalinsky and P. Oxley, Explaining the mechanics of metallic sliding friction and wear in terms of slipline field models of asperity deformation, Wear, vol.190, issue.2, pp.145-154, 1995.
DOI : 10.1016/0043-1648(96)80013-5

L. Kops and M. Arenson, Determination of Convective Cooling Conditions in Turning, CIRP Annals - Manufacturing Technology, vol.48, issue.1, pp.47-52, 1999.
DOI : 10.1016/S0007-8506(07)63129-1

I. Kragelsky, M. Dobytchin, and V. Kombalov, Friction and Wear: Calculation Methods, 1975.

H. Kuhn and D. Medlin, ASM Handbook: Mechanical Testing and Evaluation, 2000.

J. Lee and S. Lee, The effect of nozzle aspect ratio on stagnation region heat transfer characteristics of elliptic impinging jet, International Journal of Heat and Mass Transfer, vol.43, issue.4, pp.555-575, 2000.
DOI : 10.1016/S0017-9310(99)00167-2

S. Lee, J. Hwang, M. Shankar, and S. Chandrasekar, Large strain deformation field in machining, Metallurgical and Materials Transactions A, vol.47, issue.1, pp.1633-1643, 2006.
DOI : 10.1007/978-3-662-03637-2_5

D. Leseur, Experimental Investigations of Material Models for Ti?6Al?4V Titanium and 2024-T3 Aluminum, 2000.

X. Li, Study of the jet-flow rate of cooling in machining Part 1. Theoretical analysis, Journal of Materials Processing Technology, vol.62, issue.1-3, pp.1-3149, 1996.
DOI : 10.1016/0924-0136(95)02197-3

X. Li, Study of the jet-flow rate of cooling in machining Part 2. Simulation study, Journal of Materials Processing Technology, vol.62, issue.1-3, pp.1-3157, 1996.
DOI : 10.1016/0924-0136(95)02198-1

R. Liu, S. Melkote, J. Morehouse, R. Pucha, X. Man et al., An enhanced constitutive material model for machining of Ti???6Al???4V alloy, Journal of Materials Processing Technology, vol.213, issue.12, pp.2238-2246, 2013.
DOI : 10.1016/j.jmatprotec.2013.06.015

R. Liu, M. Salahshoor, S. Melkote, and T. Marusich, A unified internal state variable material model for inelastic deformation and microstructure evolution in SS304, Materials Science and Engineering: A, vol.594, pp.352-363, 2014.
DOI : 10.1016/j.msea.2013.11.071

R. Liu, M. Salahshoor, S. Melkote, and T. Marusich, The Prediction of Machined Surface Hardness Using a New Physics-based Material Model, Procedia CIRP, vol.13, pp.249-256, 2014.
DOI : 10.1016/j.procir.2014.04.043

R. Liu, M. Salahshoor, S. Melkote, J. Subramaniam, and T. Marusich, A unified material model including dislocation drag and its application to simulation of orthogonal cutting of OFHC Copper, Journal of Materials Processing Technology, vol.216, pp.328-338, 2014.
DOI : 10.1016/j.jmatprotec.2014.09.021

X. Liu, V. Lienhard, and J. Lombara, Convective Heat Transfer by Impingement of Circular Liquid Jets, Journal of Heat Transfer, vol.113, issue.3, pp.571-582, 1991.
DOI : 10.1115/1.2910604

T. Lu, A Metrics-based Sustainability Assessment of Cryogenic Machining Using Modeling and Optimization of Process Performance, 2014.

J. Luo, M. Li, W. Yu, and H. Li, The variation of strain rate sensitivity exponent and strain hardening exponent in isothermal compression of Ti???6Al???4V alloy, Materials & Design, vol.31, issue.2, pp.741-748, 2010.
DOI : 10.1016/j.matdes.2009.09.055

R. 150-]-m-'saoubi, D. Axinte, C. Herbert, M. Hardy, and P. Salmon, Surface integrity of nickel-based alloys subjected to severe plastic deformation by abusive drilling, CIRP Annals, vol.63, issue.1, pp.61-64, 2014.
DOI : 10.1016/j.cirp.2014.03.067

M. Saoubi, R. Chandrasekaran, and H. , Innovative Methods for the Investigation of Tool-Chip Adhesion and Layer Formation during Machining, CIRP Annals, vol.54, issue.1, pp.59-62, 2005.
DOI : 10.1016/S0007-8506(07)60049-3

M. Saoubi, R. Ryde, and L. , Application of the EBSD technique for the characterisation of deformation zones in metal cutting, Materials Science and Engineering: A, vol.405, issue.1-2, pp.339-349, 2005.
DOI : 10.1016/j.msea.2005.06.002

G. Ma, L. Wang, H. Gao, J. Ahang, and T. Reddyhoff, The friction coefficient evolution of a TiN coated contact during sliding wear, Applied Surface Science, vol.345, pp.109-115, 2015.
DOI : 10.1016/j.apsusc.2015.03.156

K. Maekawa, T. Shirakashi, and E. Usui, Flow Stress of Low Carbon Steel at High Temperature and Strain Rate (Part 2)?Flow Stress Under Variable Temperature and Variable Strain Rate, Bulletin of the Japan Society of Precision Engineering, vol.17, issue.3, pp.167-172, 1983.

K. Maglic, A. Cezairliyan, and V. Peletsky, Compendium of Thermophysical Property Measurement Methods, Survey of Measurement Techniques, vol.1, 1984.

X. Man, D. Ren, S. Usui, C. Johnson, and T. Marusich, Validation of Finite Element Cutting Force Prediction for End Milling, Procedia CIRP, vol.1, pp.663-668, 2012.
DOI : 10.1016/j.procir.2012.05.019

M. Martin, T. Shen, and N. Thadhani, Instrumented anvil-on-rod impact experiments for validating constitutive strength model for simulating transient dynamic deformation response of metals, Materials Science and Engineering: A, vol.494, issue.1-2, pp.416-424, 2008.
DOI : 10.1016/j.msea.2008.04.062

H. Mecking and U. Kocks, Kinetics of flow and strain-hardening, Acta Metallurgica, vol.29, issue.11, pp.1865-1875, 1981.
DOI : 10.1016/0001-6160(81)90112-7

S. Melkote, R. Liu, P. Fernandez-zelaia, and T. Marusich, A physically based constitutive model for simulation of segmented chip formation in orthogonal cutting of commercially pure titanium, CIRP Annals, vol.64, issue.1, pp.65-68, 2015.
DOI : 10.1016/j.cirp.2015.04.060

K. Minnaar and M. Zhou, An analysis of the dynamic shear failure resistance of structural metals, Journal of the Mechanics and Physics of Solids, vol.46, issue.10, pp.2155-2170, 1998.
DOI : 10.1016/S0022-5096(98)00020-9

V. Mohan and A. Balaji, On Modeling the Tool-chip Contact in Machining of Plain Carbon Steels with Multi-layer Coated Cutting Tools, Proceedings of the 5th CIRP International Workshop on Modeling of Machining Operations, pp.109-121, 2002.

A. Moufki, A. Molinari, and D. Dudzinski, Modelling of orthogonal cutting with a temperature dependent friction law, Journal of the Mechanics and Physics of Solids, vol.46, issue.10, pp.2103-2138, 1998.
DOI : 10.1016/S0022-5096(98)00032-5

S. Nemat-nasser, J. Issacs, and J. Starrett, Hopkinson Techniques for Dynamic Recovery Experiments, Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences, vol.435, issue.1894, pp.371-391, 1991.
DOI : 10.1098/rspa.1991.0150

R. Neugebauer, K. Bouzakis, B. Denkena, F. Klocke, A. Sterzing et al., Velocity effects in metal forming and machining processes, CIRP Annals, vol.60, issue.2, pp.627-650, 2011.
DOI : 10.1016/j.cirp.2011.05.001

O. Donovan, T. Murray, and D. , Jet Impingement Heat Transfer?Part I: Mean and Root-Mean-square Heat Transfer and Velocity Distributions, International Journal of Heat and Mass Transfer, vol.50, pp.17-183291, 2007.

M. Olsson, S. Soderberg, S. Jacobson, and S. Hogmark, Simulation of cutting tool wear by a modified pin-on-disc test, International Journal of Machine Tools and Manufacture, vol.29, issue.3, pp.377-390, 1989.
DOI : 10.1016/0890-6955(89)90007-2

J. Outeiro, S. Campocasso, L. Denguir, G. Fromentin, V. Vignal et al., Experimental and numerical assessment of subsurface plastic deformation induced by OFHC copper machining, CIRP Annals, vol.64, issue.1, pp.53-56, 2015.
DOI : 10.1016/j.cirp.2015.04.080

URL : https://hal.archives-ouvertes.fr/hal-01178081

J. Outeiro, D. Umbrello, M. Saoubi, and R. , Experimental and numerical modelling of the residual stresses induced in orthogonal cutting of AISI 316L steel, International Journal of Machine Tools and Manufacture, vol.46, issue.14, pp.1786-1794, 2006.
DOI : 10.1016/j.ijmachtools.2005.11.013

J. Outeiro, D. Umbrello, M. Saoubi, R. Jawahir, and I. , Evaluation of Present Numerical Models for Predicting Metal Cutting Performance And Residual Stresses, Machining Science and Technology, vol.7, issue.2, pp.183-216, 2015.
DOI : 10.1016/j.jmatprotec.2008.09.019

T. Özel, The influence of friction models on finite element simulations of machining, International Journal of Machine Tools and Manufacture, vol.46, issue.5, pp.518-530, 2006.
DOI : 10.1016/j.ijmachtools.2005.07.001

T. Özel and Y. Karpat, Identification of Constitutive Material Model Parameters for High-Strain Rate Metal Cutting Conditions Using Evolutionary Computational Algorithms, Materials and Manufacturing Processes, vol.17, issue.5, pp.659-667, 2007.
DOI : 10.1109/TEVC.2004.826069

T. Özel and E. Zeren, Determination of Work Material Flow Stress and Friction for FEA of Machining Using Orthogonal Cutting Tests, Journal of Materials Processing Technology, vol.153154, pp.1019-1025, 2004.

B. Özerdem, Measurement of convective heat transfer coefficient for a horizontal cylinder rotating in quiescent air, International Communications in Heat and Mass Transfer, vol.27, issue.3, pp.389-395, 2000.
DOI : 10.1016/S0735-1933(00)00119-6

E. Özlü, E. Budak, and A. Molinari, Analytical and experimental investigation of rake contact and friction behavior in metal cutting, International Journal of Machine Tools and Manufacture, vol.49, issue.11, pp.865-875, 2009.
DOI : 10.1016/j.ijmachtools.2009.05.005

Z. Pan, S. Liang, H. Garmestani, and D. Shih, Prediction of machining-induced phase transformation and grain growth of Ti-6Al-4??V alloy, The International Journal of Advanced Manufacturing Technology, vol.95, issue.12, pp.859-866, 2016.
DOI : 10.1063/1.1737476

W. Parker, R. Jenkins, C. Butler, and G. Abbott, Flash Method of Determining Thermal Diffusivity, Heat Capacity, and Thermal Conductivity, Journal of Applied Physics, vol.32, issue.9, pp.1679-1684, 1961.
DOI : 10.1063/1.1728417

L. Perring, J. Kuntz, F. Bussy, and J. Gachon, Heat capacity measurements by differential scanning calorimetry in the Pd???Pb, Pd???Sn and Pd???In systems, Thermochimica Acta, vol.366, issue.1, pp.31-36, 2001.
DOI : 10.1016/S0040-6031(00)00731-0

Z. Pu, S. Yang, G. Song, O. Dillon, D. Puleo et al., Ultrafine-grained surface layer on Mg???Al???Zn alloy produced by cryogenic burnishing for enhanced corrosion resistance, Scripta Materialia, vol.65, issue.6, pp.520-523, 2011.
DOI : 10.1016/j.scriptamat.2011.06.013

H. Puls, F. Klocke, and D. Lung, A new experimental methodology to analyse the friction behaviour at the tool-chip interface in metal cutting, Production Engineering, vol.5, issue.4-5, 2012.
DOI : 10.1007/s11740-011-0344-8

H. Puls, F. Klocke, and D. Lung, Experimental investigation on friction under metal cutting conditions, Wear, vol.310, issue.1-2, pp.63-71, 2014.
DOI : 10.1016/j.wear.2013.12.020

A. Ramesh and S. Melkote, Modeling of white layer formation under thermally dominant conditions in orthogonal machining of hardened AISI 52100 steel, International Journal of Machine Tools and Manufacture, vol.48, issue.3-4, pp.402-414, 2008.
DOI : 10.1016/j.ijmachtools.2007.09.007

V. Rao and O. Trass, Mass transfer from a flat surface to an impinging turbulent jet, The Canadian Journal of Chemical Engineering, vol.46, issue.3, pp.95-99, 1964.
DOI : 10.1002/aic.690050212

J. Rech, P. Arrazola, C. Claudin, C. Courbon, F. Pusavec et al., Characterization of Friction and Heat Partition Coefficients at the Tool-work Material Interface in Cutting, CIRP Annals?Manufacturing Technology, vol.61, issue.1, pp.79-82, 2013.

J. Rech, C. Claudin, W. Grzesik, and Z. Zalisz, Characterization of the friction properties of various coatings at the tool???chip???workpiece interfaces in dry machining of AISI 4140 steel, Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, vol.195, issue.3, pp.617-627, 2008.
DOI : 10.1016/j.surfcoat.2005.01.007

J. Rech, A. Kusiak, and J. Battaglia, Tribological and thermal functions of cutting tool coatings, Surface and Coatings Technology, vol.186, issue.3, pp.364-371, 2004.
DOI : 10.1016/j.surfcoat.2003.11.027

S. Rhim and S. Oh, Prediction of serrated chip formation in metal cutting process with new flow stress model for AISI 1045 steel, Journal of Materials Processing Technology, vol.171, issue.3, pp.417-422, 2006.
DOI : 10.1016/j.jmatprotec.2005.08.002

G. Rotella and D. Umbrello, Finite element modeling of microstructural changes in dry and cryogenic cutting of Ti6Al4V alloy, CIRP Annals, vol.63, issue.1, pp.69-72, 2014.
DOI : 10.1016/j.cirp.2014.03.074

W. Rowe, Thermal analysis of high efficiency deep grinding, International Journal of Machine Tools and Manufacture, vol.41, issue.1, pp.1-19, 2001.
DOI : 10.1016/S0890-6955(00)00074-2

A. Sadek, M. Attia, M. Meshreki, and B. Shi, Characterization and optimization of vibration-assisted drilling of fibre reinforced epoxy laminates, CIRP Annals, vol.62, issue.1, pp.91-94, 2013.
DOI : 10.1016/j.cirp.2013.03.097

A. Sadek, M. Meshreki, and M. Attia, Characterization and optimization of orbital drilling of woven carbon fiber reinforced epoxy laminates, CIRP Annals, vol.61, issue.1, pp.123-126, 2012.
DOI : 10.1016/j.cirp.2012.03.089

D. Sagapuram, M. Efe, W. Moscoso, S. Chandrasekar, and K. Trumble, Controlling texture in magnesium alloy sheet by shear-based deformation processing, Acta Materialia, vol.61, issue.18, pp.6843-6856, 2013.
DOI : 10.1016/j.actamat.2013.07.063

D. Sagapuram, K. Viswanathan, A. Mahato, N. Sundaram, M. Saoubi et al., Geometric flow control of shear bands by suppression of viscous sliding, Proceedings of the Royal Society A: Mathematical, Physical and Engineering Science, vol.14, issue.2192, p.47220160167, 2016.
DOI : 10.1016/j.ijmecsci.2011.10.003

D. Sagapuram, H. Yueng, Y. Guo, A. Mahato, M. Saoubi et al., On control of flow instabilities in cutting of metals, CIRP Annals, vol.64, issue.1, pp.49-52, 2015.
DOI : 10.1016/j.cirp.2015.04.059

B. Sagot, G. Antonini, A. Christgen, and F. Buron, Jet impingement heat transfer on a flat plate at a constant wall temperature, International Journal of Thermal Sciences, vol.47, issue.12, pp.1610-1619, 2008.
DOI : 10.1016/j.ijthermalsci.2007.10.020

C. Saldana, A. King, and S. Chandrasekar, Thermal stability and strength of deformation microstructures in pure copper, Acta Materialia, vol.60, issue.10, pp.4107-4116, 2012.
DOI : 10.1016/j.actamat.2012.04.022

M. San-juan, O. Martin, and F. Santos, Experimental study of friction from cutting forces in orthogonal milling, International Journal of Machine Tools and Manufacture, vol.50, issue.7, pp.591-600, 2010.
DOI : 10.1016/j.ijmachtools.2010.03.013

M. Schankula, D. Patterson, and M. Yovanovich, The Effect of Oxide Films on the Thermal Resistance Between Contacting Zirconium Alloys, Materials in Nuclear Energy, ASM, pp.106-111, 1983.

V. Schulze, J. Michna, J. Schneider, and P. Gumhsch, Modelling of cutting induced surface phase transformations considering friction effects, Procedia Engineering, vol.19, pp.331-336, 2011.
DOI : 10.1016/j.proeng.2011.11.121

V. Schulze, J. Michna, F. Zanger, C. Faltin, U. Maas et al., Influence of cutting parameters, tool coatings and friction on the process heat in cutting processes and phase transformations in workpiece surface layers???, HTM Journal of Heat Treatment and Materials, vol.68, issue.1, pp.22-31, 2013.
DOI : 10.3139/105.110177

S. Semiatin and T. Bieler, The effect of alpha platelet thickness on plastic flow during hot working of TI???6Al???4V with a transformed microstructure, Acta Materialia, vol.49, issue.17, pp.3565-3573, 2001.
DOI : 10.1016/S1359-6454(01)00236-1

L. Settineri, Surface Properties and Performance of Multilayer Coated Tools in Turning Inconel, CIRP Annals, vol.54, issue.1, pp.515-518, 2005.
DOI : 10.1016/S0007-8506(07)60158-9

L. Settineri and M. Faga, NANOSTRUCTURED CUTTING TOOLS COATINGS FOR MACHINING TITANIUM, Machining Science and Technology, vol.12, issue.2, pp.158-169, 2008.
DOI : 10.1016/S0007-8506(07)60158-9

M. Shankar, B. Rao, S. Lee, S. Chandrasekar, A. King et al., Severe plastic deformation (SPD) of titanium at near-ambient temperature, Acta Materialia, vol.54, issue.14, pp.3691-3700, 2006.
DOI : 10.1016/j.actamat.2006.03.056

M. Shankar, R. Verma, B. Rao, S. Chandrasekar, W. Compton et al., Severe Plastic Deformation of Difficult-to-Deform Materials at Near-Ambient Temperatures, Metallurgical and Materials Transactions A 38A, pp.1899-1905, 2007.
DOI : 10.1016/j.msea.2005.08.137

Y. Shao, B. Li, K. Chiang, and S. Liang, Physics-based analysis of minimum quantity lubrication grinding, The International Journal of Advanced Manufacturing Technology, vol.54, issue.55, pp.1659-1670, 2015.
DOI : 10.1016/j.ijmachtools.2011.11.009

M. Shaw, Metal cutting principles, Tribology International, vol.18, issue.1, 2005.
DOI : 10.1016/0301-679X(85)90013-1

G. Shi, X. Deng, and C. Shet, A finite element study of the effect of friction in orthogonal metal cutting, Finite Elements in Analysis and Design, vol.38, issue.9, pp.863-883, 2002.
DOI : 10.1016/S0168-874X(01)00110-X

J. Shi and C. Liu, The Influence of Material Models on Finite Element Simulation of Machining, Journal of Manufacturing Science and Engineering, vol.126, issue.4, pp.849-857, 2004.
DOI : 10.1115/1.1813473

T. Shirakashi and E. Usui, Friction Characteristics on Tool Face in Metal Machining, Journal of the Japan Society of Precision Engineering, vol.39, issue.464, pp.966-972, 1973.
DOI : 10.2493/jjspe1933.39.966

M. Sima and T. Özel, Modified material constitutive models for serrated chip formation simulations and experimental validation in machining of titanium alloy Ti???6Al???4V, International Journal of Machine Tools and Manufacture, vol.50, issue.11, pp.943-960, 2010.
DOI : 10.1016/j.ijmachtools.2010.08.004

D. Smolenicki, J. Boos, F. Kuster, H. Roefolds, and C. Wyen, In-process measurement of friction coefficient in orthogonal cutting, CIRP Annals, vol.63, issue.1, pp.97-100, 2014.
DOI : 10.1016/j.cirp.2014.03.083

N. Suh and H. Sin, The genesis of friction, Wear, vol.69, issue.1, pp.91-114, 1981.
DOI : 10.1016/0043-1648(81)90315-X

A. Svoboda, D. Wedberg, and L. Lindgren, Simulation of metal cutting using a physically based plasticity model, Modelling and Simulation in Materials Science and Engineering, vol.18, issue.7, p.75005, 2010.
DOI : 10.1088/0965-0393/18/7/075005

S. Tajalli, M. Movahhedy, and J. Akbari, Simulation of orthogonal micro-cutting of FCC materials based on rate-dependent crystal plasticity finite element model, Computational Materials Science, vol.86, pp.79-87, 2014.
DOI : 10.1016/j.commatsci.2014.01.016

Y. Touloukian, R. Kirby, E. Taylor, and T. Lee, Thermophysical Properties of Matter?The TPRC Data Series, Thermal Expansion?Nonmetallic Solids Thermophysical and Electronic Properties Information Analysis Center, 1977.

Y. Touloukian, R. Powell, C. Ho, and M. Nicolaou, Thermophysical Properties of Matter?The TPRC Data Series, IFI/Plenum Data Corporation, 1974.

D. Ulutan and T. Özel, Determination of tool friction in presence of flank wear and stress distribution based validation using finite element simulations in machining of titanium and nickel based alloys, Journal of Materials Processing Technology, vol.213, issue.12, pp.2217-2237, 2013.
DOI : 10.1016/j.jmatprotec.2013.05.019

D. Ulutan, M. Sima, and T. Özel, Prediction of Machining Induced Surface Integrity Using Elastic-Viscoplastic Simulations and Temperature-Dependent Flow Softening Material Models in Titanium and Nickel-Based Alloys, Advanced Materials Research, vol.223, pp.401-410, 2011.
DOI : 10.4028/www.scientific.net/AMR.223.401

D. Umbrello and L. Filice, Improving surface integrity in orthogonal machining of hardened AISI 52100 steel by modeling white and dark layers formation, CIRP Annals, vol.58, issue.1, pp.73-76, 2009.
DOI : 10.1016/j.cirp.2009.03.106

D. Umbrello, J. Outeiro, M. Saoubi, R. Jayal, A. Jawahir et al., A numerical model incorporating the microstructure alteration for predicting residual stresses in hard machining of AISI 52100 steel, CIRP Annals, vol.59, issue.1, pp.113-116, 2010.
DOI : 10.1016/j.cirp.2010.03.061

M. Vaz, E. Cardoso, P. Munoz-rojas, T. Carniel, M. Leursen et al., Identification of constitutive parameters - optimization strategies and applications, Materialwissenschaft und Werkstofftechnik, vol.19, issue.259, pp.4-5477, 2015.
DOI : 10.1177/1056789508098314

M. Vogler, R. Devor, and S. Kapoor, On the Modeling and Analysis of Machining Performance in Micro-Endmilling, Part I: Surface Generation, Journal of Manufacturing Science and Engineering, vol.126, issue.4, pp.685-694, 2004.
DOI : 10.1115/1.1813470

D. Wedberg, A. Svoboda, and L. Lindgren, Modelling high strain rate phenomena in metal cutting simulation, Modelling and Simulation in Materials Science and Engineering, vol.20, issue.8, p.85006, 2012.
DOI : 10.1088/0965-0393/20/8/085006

Y. Yen, J. Söhner, B. Lilly, and T. Altan, Estimation of tool wear in orthogonal cutting using the finite element analysis, Journal of Materials Processing Technology, vol.146, issue.1, pp.82-91, 2004.
DOI : 10.1016/S0924-0136(03)00847-1

M. Yovanovich, S. Burde, and J. Thompson, Thermal constriction resistance of arbitrary planar contacts with constant flux, 11th Thermophysics Conference, pp.1-6, 1976.
DOI : 10.2514/6.1976-440

S. Zahedi, M. Demiral, A. Roy, and V. Silberschmidt, FE/SPH modelling of orthogonal micro-machining of f.c.c. single crystal, Computational Materials Science, vol.78, pp.104-109, 2013.
DOI : 10.1016/j.commatsci.2013.05.022

F. Zemzemi, W. Bensalem, J. Rech, A. Dogui, and P. Kapsa, New Tribometer Designed for the Characterization of the Friction Properties at the Tool, Workpiece Interfaces in Machining. Tribo Test, vol.14, pp.11-25, 2008.

F. Zemzemi, J. Rech, W. Bensalem, A. Dogui, and P. Kapsa, Development of a friction model for the tool-chip-workpiece interfaces during dry machining of AISI4142 steel with TiN coated carbide cutting tools, International Journal of Machining and Machinability of Materials, vol.2, issue.3/4, pp.361-377, 2007.
DOI : 10.1504/IJMMM.2007.015472

F. Zemzemi, J. Rech, W. Bensalem, A. Dogui, and P. Kapsa, Identification of Friction and Heat Partition Model at the Tool-chip-workpiece Interfaces in Dry Cutting of an Inconel718 Alloy with CBN and Coated Carbide Tools, Advances in Manufacturing Science and Technology, vol.38, issue.1, 2007.

F. Zerilli, Dislocation mechanics-based constitutive equations, Metallurgical and Materials Transactions A, vol.1, issue.9, pp.2547-2555, 2004.
DOI : 10.1016/B978-0-444-89732-9.50058-3

F. Zerilli and R. Armstrong, Dislocation???mechanics???based constitutive relations for material dynamics calculations, Journal of Applied Physics, vol.46, issue.5, pp.1816-1825, 1987.
DOI : 10.1063/1.1707363

P. Zhang, G. Xu, X. Fu, and C. Li, Confined jet impingement of liquid nitrogen onto different heat transfer surfaces, Cryogenics, vol.51, issue.6, pp.300-308, 2011.
DOI : 10.1016/j.cryogenics.2010.06.018

Y. Zhang, T. Mabrouki, D. Nelias, C. Courbon, J. Rech et al., Cutting simulation capabilities based on crystal plasticity theory and discrete cohesive elements, Journal of Materials Processing Technology, vol.212, issue.4, pp.936-953, 2012.
DOI : 10.1016/j.jmatprotec.2011.12.001

URL : https://hal.archives-ouvertes.fr/hal-00938429

F. Zhou, A new analytical tool-chip friction model in dry cutting, The International Journal of Advanced Manufacturing Technology, vol.43, issue.287, pp.309-319, 2014.
DOI : 10.1016/S0020-7403(99)00105-8

N. Zuckerman and N. Lior, Jet Impingement Heat Transfer: Physics, Correlations , and Numerical Modeling Advances in Heat Transfer, pp.39-565, 2006.